Rigid and precise by design
Exceptionally rigid frames feature custom extrusion designs, engineered for stiffness.
Factory compensation of test frames and force sensors ensure position accuracy of
±0.002 in / 0.05 mm under any load, at any position.
Stepper motors and controllers drive a ballscrew and linear guideway for smooth, quiet operation, with virtually no speed variation under load.
Conveniently modular
Frame bases can be removed to accommodate column extensions and alternative mo-
unting configurations. Most electronics are housed in a self-contained enclosure, easily
accessed and replaced if needed. Integrated T-slots along the column accommodate add-ons.
External limit switches
Solid-state upper and lower limit switches may be used as test limits or as test exceptions.
Dual-graduated rulers aid in switch placement.
Seamless force sensor interface
Series FS05 smart force sensors mount directly to the crosshead of models F105, F305, F505,
and F505H, without any connection cables. Ranges available from 0.12 to 500 lbF [0.5 N to
2.5 kN]. Accurate to ±0.1% of full scale.
Series R07 S-beam type force sensors accommodate higher force ranges, also compatible with
Plug & Test® technology. Ranges available from 50 to 1,500 lbF [250 N to 7.5 kN]. Accurate
to ±0.15% of full scale.
Easy-to-service electronics
Most electronics are housed in an integrated module, easily replaced without special
tools or processes.
IntelliMESUR® software is an integrated solution running on Windows tablets and PCs.
Select a pre-loaded 10.1” tablet with mounting bracket or use your own Windows device. With IntelliMESUR®, you can create and run a wide range of basic and multi-step tests, including:
- Limit testing to a load, break, or distance
- Height measurement
- Load holding
- Cycle testing
- Multi-step testing, utilizing any combination of the above functions
Run individual runs or batches, and view data in graphical format or results tables. Save or export data as needed, or generate a report.
Ready. Set. Go.
From IntelliMESUR®’s home screen, quickly access up to 10 favorite tests. Associate an
image with each favorite for easy identification.
What’s your point of view?
Run a test via the Graph or Results views, and switch views as needed. Pass / Fail indicator easily identifies problematic samples. Individual runs may be invalidated if, for example, the sample slips out of the grips, or the test was interrupted.
Results View
The Results view displays user-selected results for each run.
Statistics may be applied to selected results.
Graph View
The Graph view plots force vs. distance or force vs. time. Overlay
up to 10 runs for visual comparisons.
Test setup is easy as 1-2-3
1. Pre-Test Settings | 2. Test Settings | 3. Results & Statistics Selection |
Units of measurement | Test objective | Final load |
Batch size | Speed | Maximum load |
Display preferences | Pass / fall limits | Minimum load |
Preload | Exception limits | Load at max. distance |
Operator prompts | Load at min. distance | |
Load at break | ||
Average load | ||
Delta load | ||
Maximum distance | ||
Final distance | ||
Minimum distance | ||
Height | ||
Distance at max. load | ||
Distance at min. load | ||
Distance at break | ||
Delta distance | ||
Area under the curve |
Multi-step tests
Building upon basic test wizards, easily incorporate any combination of steps, with
the ability to loop a sequence of steps. Select from:
- Move to load
- Move to distance
- Move to break
- Hold a load or position
- Hold a load or position
- Loop / cycle
- Datum
- Prompts
- Save current load or position
- Zero load or position
- Return to Home position
Operator prompting
Prompts can appear at the beginning of each test, batch, or run.
Ask prompts ask the operator for information which is saved in the results table
– for example, a lot number. Type the response or use a barcode scanner.
Tell prompts provide instructions to the operator, and can include an image.
Take your measurements to new heights
Use Height Mode to determine height at a specific load, commonly used in spring
testing. A datum may be set to define the reference point.
Deflection compensation
Series F test frames and force sensors are deflection-compensated at the factory,
resulting in system distance measurement accuracy of ±0.002 in / 0.05 mm at any
load and at any position along the frame. To further compensate grips and attachments, use
IntelliMESUR®’s deflection compensation utility. The deflection offset file can be
associated with the test setup file.
Robust data acquisition and management
Blazingly fast
Force sensor sampling rate of 20,000 Hz yields accurate peak measurements even
in quick-duration events. IntelliMESUR® collects load and travel data at up
to 1,000 Hz, and allows up to 1 million data points per run.
Customizable reporting
Print or create a PDF report, including results, statistics, graph, system and user information, and comments. Personalize the report with your company logo and an additional image.
Create report templates to save with future reports.
Save or export data
Automatically or manually save individual runs and results to a USB drive or file location of
your choice. File names are automatically generated with the test name and time stamp, for quick searchability.
Results sets and data from individual runs may also be exported as .csv files.
Intelligent manual control
Manually control the test frame to obtain quick force and distance results, or manually position the crosshead prior to a test. Select from several actuation methods, including momentary (button-hold), maintained (button release) motion, jog mode with three distance presets, and FollowMe® force-based positioning.
Push and pull on the force sensor to move the crosshead. Apply greater
force to achieve faster motion. FollowMe® is responsive
enough for quick positioning as well as fine adjustments.
The Height / Length Offset utility in Manual Control defines a reference point
to accommodate applications in which grips cannot directly touch one another.
Calibrate force sensors on the test frame or off-site
Calibrate Series FS05 and R07 force sensors in one of two ways:
Test frame
IntelliMESUR® provides an integrated utility, with an intuitive step-by-step wizard. Manual controls allow the technician to use the test frame to apply tension and compression forces.
Off-site
Conveniently remove the force sensors for off-site calibration with a Mark-10 Model
M7I or M5I indicator (requires optional AC1083 adapter).
Secure user access
Control user access with three permissions levels:
- Administrators have full access.
- Supervisors can create a test, run reports, calibrate force sensors, and change settings.
- Operators may recall and run a test, but cannot create a test or perform more advanced functions.
Specifications
F105 | F305 | F505 | F505H | |
Load capacity*: | 100 lbF [0.5 kN] |
300 lbF [1.5 kN] |
500 lbF [2.2 kN] |
|
Maximum travel: | 18.0 in [457 mm] |
|||
Speed range: | 0.02 – 45 in/min [0.5 – 1,100 mm/min] |
|||
Load accuracy (% of full scale) |
•Test frame: ±0.1% •Force sensor alone: Series FS05: ±0.1% | Series R07: ±0.15% |
|||
Data acquisition rate: | 1,000 Hz | |||
Speed accuracy: | ±0.2% of setting, virtually no variation with load | |||
Distance accuracy: | ±0.002 in [0.05 mm], factory-compensated at up to full load | |||
Distance resolution: | 0.0005 in [0.01 mm] | |||
Limit switch repeatability: | ±0.001 in [0.03 mm] | |||
Power: | Universal input 100-240 VAC, 50/60 Hz, 300W | |||
Fuse type: | 1.2 A, 250V, 3AG, SLO BLO | |||
Weight (test frame only): | 60 lb [27 kg] |
70 lb [32 kg] |
||
Shipping weight: | 75 lb [34 kg] |
85 lb [39 kg] |
||
Environmental conditions: | Indoor use only Up to 6,500 ft [2,000 m] above sea level Temperature range: 40 – 95°F [5 – 35°C] Humidity range: up to 80% relative humidity at 31°C, decreasing linearly to 50% relative humidity at 40°C, non-condensing Mains supply voltage fluctuations up to ±10 % of the nominal voltage Transient overvoltages up to the levels of Overvoltage Category II Use in environments up to Pollution Degree 2 |
|||
Conformance: | CE | |||
Warranty: | 3 years [see individual statement for further details] |
* Load capacity is reduced at higher speeds, as follows:
– F305: limited to 200 lbF [1 kN] above 24 in [610 mm]/min
– F505 / F505H: limited to 300 lbF [1.5 kN] above 24 in [610 mm]/min
In The Box (IMT Models)
The F105-IMT, F305-IMT, F505-IMT, and F505H-IMT advanced test frames are shipped as shown at left, and includes the following accessories:
(1) Control panel, mounting bracket, and hardware
(1) Mounting bracket, column end (F505H only)
(1) USB cable
(1) #10-32M medium hook
(1) 5/16-18M large hook
(1) #10-32F 2” diameter compression plate
(1) #10-32 M/F 2” extension rod
(1) #10-32 F/F coupler
(1) Adapter, 5/16-18M to #10-32F
(1) Set screw, #10-32 x 3/4”
(2) Hex nut, #10-32
(1) Power cord
(1) Allen wrench set
(1) NIST-traceable certificate of calibration, force
Series FS05 force sensors Measure tension and compression forces. Mount directly to the test frame’s crosshead without any cables. Capacities from 0.12 to 500 lbF [0.5 to 2,500 N]. |
|
Control panel tabletop mounting kit (AC1085) For applications requiring remote use of the control panel. Features an adjustable viewing angle and a base with thru holes for bench mounting. |
|
Safety shield (AC1086) Provides pinch and sample debris protection for the operator. Includes an electrical interlock, preventing operation while the door is open. |
|
Single column extensions (AC1094-1 / -2 / -3) Increase the vertical clearance for tall samples. Multiple extensions may be stacked for very long samples.Three lengths are available – 6, 12 and 24 in [150, 300, and 600 mm].Not compatible with the AC1086 safety shield. |
|
Double column extensions (AC1095-1 / -2 / -3) Accommodate up to a 20 in. [508 mm] wide sample, or ø21.5 in [ø546 mm] round sample.Three heights are available – 6, 12 and 24 in [150, 300, and 600 mm]. Base contains rows of T-slots for fixture mounting.Not compatible with the AC1086 safety shield. |
|
USB hub (AC1093) Test frame-mounted 4-port USB hub improves cable management and conveniently accommodates peripherals, such as a flash drive, barcode scanner, etc. Compatible with all Series F test frames. |
|
Eye end adapters Allow for quick grip installation and removal, and prevent grip rotation. Mount to common test frames, load cells, and force gauges. |
|
Adapter, FS05 to Plug & Test® connector Adapts a Series FS05 force sensor or PTAF sensor adapter to Plug & Test® type interface, for ease of external calibration via a Mark-10 indicator. Also permits mounting of a Series FS05 sensor to Models F755, F755S, F1505, and F1505S test frames. |
|
Third-party sensor adapter (PTAF) Adapt a third-party party force sensor to Series F frames and Models M5I and M7I indicators. |
Model | Description | US Price |
---|---|---|
Test Frame + Pre-configured Tablet Control Panel | ||
F755-IMT | Test frame with IntelliMESUR® pre-loaded tablet control panel, vertical, 750 lbF / 3.4 kN, 110V* | $12,950.00 |
F755S-IMT | Test frame with IntelliMESUR® pre-loaded tablet control panel, vertical, short, 750 lbF / 3.4 kN, 110V* | $12,350.00 |
F1505-IMT | Test frame with IntelliMESUR® pre-loaded tablet control panel, vertical, 1,500 lbF / 6.7 kN, 110V* | $14,150.00 |
F1505S-IMT | Test frame with IntelliMESUR® pre-loaded tablet control panel, vertical, short, 1,500 lbF / 6.7 kN, 110V* | $13,550.00 |
Test Frame + Standalone Software (for customer installation on a Windows device) | ||
F755-IM | Test frame with IntelliMESUR® software, single license, vertical, 750 lbF / 3.4 kN, 110V* | $11,150.00 |
F755S-IM | Test frame with IntelliMESUR® software, single license, vertical, short, 750 lbF / 3.4 kN, 110V* | $10,550.00 |
F1505-IM | Test frame with IntelliMESUR® software, single license, vertical, 1,500 lbF / 6.7 kN, 110V* | $12,350.00 |
F1505S-IM | Test frame with IntelliMESUR® software, single license, vertical, short, 1,500 lbF / 6.7 kN, 110V* | $11,750.00 |
Mark-10 F1505S-IM Advanced Test Frames